Utilizing a serger for routine sewing tasks is a fantastic alternative, since it will complete the task quickly. Multiple threads are used by the sewing machine to sew distinct and overcast raw edges.
Serger For Regular Sewing: Sergers are utilised well for finishing, structures, and occasionally both. This may involve between two and eight threads. It depends on the serger’s model and manufacturer, as well as the selected stitch.
This article discusses the normal sewing tasks that can be accomplished using a serger. You will learn everything from the most impressive methods to the necessary tools for using a serger.
Yes, a serger may be used for everyday sewing. Rather, it is a good option because it will accomplish the task efficiently. Multiple threads are used by the sewing machine to sew distinct and overcast raw edges.
There are lot of information about overlock and serger machines check this site: Mrsewguru.com
How To Use A Serger For Regular Sewing
Sewing with a serger is basic and straightforward. To use a serger efficiently, you must follow a few procedures. Look below!
Initial Step: Threading The Serger
Power down the machine.
Before using the serger, it is necessary to place the threads on it. To accomplish this, you must turn off the machine. Locate the power button and deactivate the device.
Determine the correct threading sequence
Not all sergers are identical. Some have four thread spools, while others have two or three. Therefore, prior to utilising the machine, the threading order must be determined.
Install a thread spool on the upper looper.
The upper looper of the serger is positioned on the sewing machine’s right side. Ensure that a thread spool is attached to the correct set of the spindle for this one.
Insert the upper looper
Pull the upper looper’s thread so that it is beneath the needle. Remove the machine’s faceplate. Then, draw the metal loops directly under the plate.
There is a color-coded guidance on the serger that will help you thread the upper looper.
Insert the lower looper
Place the thread spool on the second spindle before bringing it across the front of the serger. You can use tweezers to thread the thread through the sewing machine’s tight spaces.
Knit the needles.
After setting the threads on the spindle, the following step is to bring the spindle to the front of the serger. Insert the thread directly between the needles or needles on the sewing machine.
Second Step: Adjusting The Serger
Engage the serger.
In order to adjust the sewing machine tension, it is necessary to power on the machine.
Choose the desired stitch type.
Sewing machines like the serger machines may gather fabric, produce a rolled hem, and finish the raw knit edges, among other capabilities. For these reasons, you must first choose the desired stitch before you can get the intended effects.
Adjust the tension dial on each individual spool.
After determining the desired stitch type, you must change the tension dial on each spool of thread. In the machine’s instruction manual, the needed tension for each spool is specified.
Perform a sample stitch.
Everything is in position, and you must test the stitch by placing fabric beneath the needles. When the foot pedal is depressed, the machine will create a looping thread.
Examine the loop thread
By consulting the guidebook, you will gain an understanding of how the stitches on a serger will seem. The interlocking and loop stitches will be uniform, with no slack or uneven spots.
Try tightening the stitches by changing the tension dial adjacent to the thread spool on the serger if they are excessively loose. Conversely, if the fabric becomes bunched, loosen the tension dial.
Practice on scraps of cloth
Examine a piece of fabric or scrap fabric to test the stitch. You must continuously examine the stitches until they are uniform.
Step Three: Finishing Seams
Raise the needles as well as the presser foot.
Raise the presser foot lever so that the metal pressure foot can be raised. Then, rotate the needle dial toward you and raise the needles.
Place the fabric beneath the needle and foot.
When cloth is slid beneath the needle and presser foot, the practise string must be raised.
Reduce the needles and foot height.
To lower the presser foot, you must lower the presser lever and tilt the needle dial towards you to lower the needle position.
Remove the cloth’s hems from the edges of the fabric.
The serger will simultaneously cut the fabric and finish the seams. The seam allowance number will be located on the right side of the needle, and the material will be fed through the blade.
This could range between 1.5cm and 2.5cm depending on the seal allowance used to measure the cloth or fabric.
Under the needle, guide and stitch the fabric.
Utilize the foot pedal to achieve a good degree of speed control. Avoid excessive fabric stretching, and be sure to maintain the fabric straight. The foot of the serger will aid in fabric movement.
Create a tail stitch
Continue stitching a few additional stitches at the seam’s end to create a tail of stitches. You can either hand-sew or tuck the stitches’ bottoms into place.
